Click here for product information pb rohs_mat rohs_comp  msds

Wound Beads (2944777741)

Part Number: 2944777741
44 WOUND BEAD
44 Material
Suppression Components
Board Component
Printer Friendly Data Sheet
Check Stock

Part Number: 2944777741

44 WOUND BEAD

Explanation of Part Numbers:
– Digits 1 & 2 = Product Class
– Digits 3 & 4 = Material Grade
– Last digit 1 = Bulk Packed 4 = Taped and Reeled

Six and eleven hole beads, in two NiZn materials, are available both as beads (product class 26) and wound with tinned copper wire in several winding configurations (product class 29).

Wire used for winding is oxygen free high conductivity copper with 100% matte tin plating over a nickel undercoating.

Recommended storage temperature and operating temperature is -55 °C to 125 °C

Recommended Soldering Profile

Packaging Options:
– Parts with a 1 as the last digit of the part number are supplied bulk packed. Wound beads with part numbers 29–666631 and 29–666651 can be supplied radially taped and reeled per IEC 60286-1 and EIA 468-B standards. For these taped and reeled wound beads the last digit of the part number is a 4. Taped and reeled wound beads are supplied 500 pieces on a 13 reel.

For any wound bead requirement not listed in here, please contact our customer service group for availability and pricing. 

Catalog Drawing
3D Model

Weight: 3.8 (g)

Dimmmmm tolnominal inchinch misc.
A10±0.250.394_
B0.9+0.150.038_
C10±0.250.394_
D7.5Ref0.295Ref
Winding Information
Turns TestsWire Size1st Wire Length2nd Wire Length
0.65
22 AWG
38.0 ±3.0
(1.496”)
_

Chart Legend
+ Test frequency
•A ½ turn is defined as a single pass through a hole.

Typical Impedance (Ω)
1 MHz180
10 MHz+870
50 MHz+1994
100 MHz+1400
200 MHz760

Beads are controlled for impedance limits only. Minimum impedance values are specified for the + marked frequencies. The minimum impedance is typically the listed impedance less 20%.

Catalog Drawing

The 44 material beads and wound beads are tested on the E4990A Impedance Meter. The 61 material parts on the E4991A / HP4291B Impedance Analyzer.

Typical Impendance (Ω)
1 MHz 150
10 MHz+ 815
50 MHz+ 1250
100 MHz+ 500
200 MHz 375

CSV Download

A NiZn ferrite developed to combine a high suppression performance, from 30 MHz to 500 MHz, with a very high DC resistivity.

Available in 44 material:
SM Beads
PC Beads
Wound Beads
Round Cable Snap-Its
Connector EMI Suppression Plates

44 Material Characteristics
Property Unit Symbol Value
Initial Permeability@ B < 10 gauss µi 500
Flux Density @ Field Strength Gauss
Oersted
B
H
3000
10
Residual Flux Density Gauss Br 1100
Coercive Force Oersted Hc 0.45
Loss Factor @ Frequency 10 -6
MHz
Tan δ/ µi 150
1.0
Temperature Coefficient of Initial Permeability (20 -70°C) % / °C 1.6
Curie Temperature °C Tc >160
Resistivity ohm-cm ρ 1×109

**** Characteristic curves are measured on standard Toroids (18/10/6 mm)  at 25°C and 10 kHz unless otherwise indicated. Impedance characteristics are measured on standard shield beads (3.5/1.3/6.0 mm) unless otherwise indicated.

Material Safety Data Sheet (MSDS)

Click here to download Complex Permeability vs. Frequency (CSV)

Ferrite Material Constants

Specific Heat
0.25 cal/g/°C
Thermal Conductivity
3.5 - 4.5 mW/cm-°C
Coefficient of Linear Expansion
8 - 10x10-6/°C
Tensile Strength
4.9 kgf/mm2
Compressive Strength
42 kgf/mm2
Young's Modulus
15x103 kgf/mm2
Hardness (Knoop)
650
Specific Gravity
≈4.7 g/cm3
The above quoted properties are typical for Fair-Rite MnZn and NiZn ferrites.


Storage and Operating Temperature
Printer Friendly Data Sheet - Download as pdf file

Go to Top