Click here for product information pb rohs_mat rohs_comp  msds

SM Beads (Differential-Mode)

Part Number: 2773021446
73 SM BEAD
Lower Frequencies < 50 MHz (73 material)
Suppression Components
Board Component
Printer Friendly Data Sheet
Check Stock

Part Number: 2773021446

73 SM BEAD

Explanation of Part Numbers:
– Digits 1 & 2 = Product Class
– Digits 3 & 4 = Material Grade
•– Last digit 6 = Bulk Packed, 7 = Taped and Reeled

Surface mount beads are available from Fair-Rite in several materials and sizes. Their rugged construction lowers the dc resistance and increases current carrying capacity compared to plated beads.

•Wires are oxygen free high conductivity copper with 100% matte tin plating over a nickel undercoating.

•SM Beads meet the solderability specifications when tested in accordance with MIL-STD-202, method 208. After dipping the mounting site of the bead, the solder surface shall be at least 95% covered with a smooth solder coating. The edges of the copper strip are not specified as solderable surfaces.

•After preheating the beads to within 100 °C of the soldering temperature, the parts meet the resistance to soldering requirements of EIA-186-10E, temperature 260 ±5 °C and time 10 ±1 seconds.

•Recommended storage and operation temperature is -55 °C to 125 °C.

•Our “Surface Mount Bead Kit” (part number 0199000025) is available for prototype evaluation.

Packaging Options:
••– SM Beads on 12 mm tape width are supplied taped and reeled per EIA 481 and IEC 60286-3 standards. SM Beads on 16 and 24 mm tape widths are supplied taped and reeled per EIA 481 and IEC 60286-3 standards. Taped and reeled parts are supplied on a 13″ reel.
•– SM Beads can also be supplied not taped and reeled and then are bulk packed. This packing method will change the last digit of the part number to a “6”.

•For any SM Bead requirement not listed, please contact our customer service group for availability and pricing.

Suggested land patterns are in accordance with the latest revision of IPC-7351.

Weight: 0.3 (g)

Dimmmmm tolnominal inchinch misc.
A2.85±0.200.112_
B3.05±0.100.12_
C9.6-0.950.359_
D1.5±0.500.059_
Land Patterns
VWXYZ
4.50
(0.177”)
7.50
(0.295”)
1.80
(0.071”)
3.00
(0.118”)
_

Chart Legend
+ Test frequency

Typical Impedance (Ω)
1 MHz25
5 MHz50
10 MHz+60
25 MHz+78
Electrical Properties
Max
Rdc(mΩ)
1.2

•SM Beads are controlled for impedance limits only. Minimum impedance values are specified for the + marked frequencies. The minimum impedance is typically the listed value less 20%. SM Beads in 73, 43 and 44 materials are measured for impedance on the 4193 Vector Impedance Analyzer. The 52 and 61 SM Beads are tested for impedance on the 4291A RF Impedance Analyzer.

•The maximum practical current rating for these SM Beads is 5 amps, check the component bias curves. The 019/021/037
and 044 SM Beads can withstand a continuous current of 10 amps resulting in a component temperature rise < 40 °C

Typical Impendance (Ω)
1 MHz 25
5 MHz 50
10 MHz+ 60
25 MHz+ 78

A MnZn ferrite supplied only in small cores to suppress conducted EMI frequencies below 50 MHz.

Available in 73 material:
EMI Suppression Beads
Beads On Leads
SM beads
Multi-Aperture Cores

73 Material Characteristics
Property Unit Symbol Value
Initial Permeability @ B < 10 gauss µi 2500
Flux Density @ Field Strength Gauss
Oersted
B
H
3900
5
Residual Flux Density Gauss Br 3200
Coercive Force Oersted Hc 0.28
Loss Factor @ Frequency 10 -6
MHz
Tan δ/ µi 20
0.1
Temperature Coefficient of Initial Permeability (20 -70°C) %/°C 1.3
Curie Temperature °C Tc >130
Resistivity ohm-cm ρ 3000

**** Characteristic curves are measured on standard Toroids (18/10/6 mm)  at 25°C and 10 kHz unless otherwise indicated. Impedance characteristics are measured on standard shield beads (3.5/1.3/6.0 mm) unless otherwise indicated.

Ferrite Material Constants

Specific Heat
0.25 cal/g/°C
Thermal Conductivity
3.5 - 4.5 mW/cm-°C
Coefficient of Linear Expansion
8 - 10x10-6/°C
Tensile Strength
4.9 kgf/mm2
Compressive Strength
42 kgf/mm2
Young's Modulus
15x103 kgf/mm2
Hardness (Knoop)
650
Specific Gravity
≈4.7 g/cm3
The above quoted properties are typical for Fair-Rite MnZn and NiZn ferrites.


Storage and Operating Temperature
Printer Friendly Data Sheet - Download as pdf file

You must be signed in to use the forums

Need an account? Sign Up Here

Fill your details to signup

Have an account? Login Here