Click here for product information pb rohs_mat rohs_comp  msds

Rods (4077374711)

Part Number: 4077374711
77 SOLID ROD
Medium Permeability, 77 (ui=2000) & 78 (ui=2300) materials
Inductive Components
Open Magnetic Circuit
Printer Friendly Data Sheet
Check Stock

Part Number: 4077374711

77 SOLID ROD

Explanation of Part Numbers:
– Digits 1 & 2 = Product Class
– Digits 3 & 4 = Material Grade

Pressed Fair-Rite rods are used extensively in high-energy storage designs.

These rods can also be used for inductive components that require temperature stability or have to accommodate large dc bias requirements.

Figure 2 rods have a 0.6 mm (0.024”) maximum chamfer on the end faces.

For frequency tuned rod designs see section “Antenna/RFID Rods”.

•For any rod requirement not listed here, feel free to contact our customer service group for availability and pricing.

The “A” dimension can be centerless ground to tighter tolerances.

Weight: 11 (g)

Dimmmmm tolnominal inchinch misc.
A9.45±0.200.372_
C31.75±0.751.25_

Figure 1 shows the rod permeability as a function of the length to diameter ratio for the six materials available in rods.

Figures 3, 4 and 5 illustrate typical temperature behavior of wound rods. Would rods in 33 and 77 material yield the best temperature stable inductors, see Figure 4. Both show a typical inductance change of <1% over the -40° to 120°C temperature range. The parts have a L/D ratio of 8.1. Lower ratios will change less. This is shown in detail in Figure 5 for the same 52 material but with the L/D ratio as the parameter. A lower ratio means a lower rod permeability but with improved temperature stability.

Figure1&2

Wound Rod Inductance Calculations

To calculate the inductances of a wound rod the following formula can be used,

 WoundFormula

The inductance modifier is found in Figure 2. The ratio winding length divided by the rod length will give the inductance modifier. If the rod is totally wound the K=1. Shorter but centered winding will yield higher K values.

 Using the rod 3061990871 as an example.

For this rod the length over diameter ratio is 8.33 and for 61 material Figure 1 gives a µrod of 29. The rod has an AE= 0.0707 cm² and 𝓁=2.5 cm.

A winding of 80 turns of 30 AWG wire will yield a fully wound rod, therefore K=1.

Using the formula the calculated inductance is 65.96µH.

 The measured values for both winding were 66.95 and 39.50µH respectively.

 Figures3-5

 

A MnZn ferrite for use in a wide range of high and low flux density inductive designs for frequencies up to 100 kHz.

Available in 77 material:

Pot Cores

E&I Cores

U Cores

Rods

Toroids

Bobbins

77 Material Characteristics
Property Unit Symbol Value
Initial Permeability @ B < 10 gauss µi 2000
Flux Density @ Field Strength Gauss
Oersted
B
H
5100
5
Residual Flux Density Gauss Br 1800
Coercive Force Oersted Hc 0.25
Loss Factor @ Frequency 10 -6
MHz
Tan δ/ µi 15
0.1
Temperature Coefficient of Initial Permeability (20 -70°C) %/°C 0.7
Curie Temperature °C Tc >200
Resistivity ohm-cm ρ 100

**** Characteristic curves are measured on standard Toroids (18/10/6 mm)  at 25°C and 10 kHz unless otherwise indicated. Impedance characteristics are measured on standard shield beads (3.5/1.3/6.0 mm) unless otherwise indicated.

Ferrite Material Constants

Specific Heat
0.25 cal/g/°C
Thermal Conductivity
3.5 - 4.5 mW/cm-°C
Coefficient of Linear Expansion
8 - 10x10-6/°C
Tensile Strength
4.9 kgf/mm2
Compressive Strength
42 kgf/mm2
Young's Modulus
15x103 kgf/mm2
Hardness (Knoop)
650
Specific Gravity
≈4.7 g/cm3
The above quoted properties are typical for Fair-Rite MnZn and NiZn ferrites.


Storage and Operating Temperature
Printer Friendly Data Sheet - Download as pdf file

You must be signed in to use the forums

Need an account? Sign Up Here

Fill your details to signup

Have an account? Login Here