Click here for product information pb rohs_mat rohs_comp  msds

PC Beads (Through Hole)

Part Number: 2944778301
44 PC BEAD
44 Material
Suppression Components
Board Component
Printer Friendly Data Sheet
Check Stock

Part Number: 2944778301

44 PC BEAD

Explanation of Part Numbers:
– Digits 1 & 2 = Product Class
– Digits 3 & 4 = Material Grade
– Last digit 1 = Standard Wire Length 2.4 mm (0.095″) Minimum, 2 = Wire Length 3.1 mm (0.122) Minimum

Multiple single turn or multi-turn printed circuit EMI suppression beads are available in two Fair-Rite materials. The broadband 44 material and in the high frequency 52 material grade.

Wires are oxygen free high conductivity copper with 100% matte tin plating over a nickel undercoating. Wires on top of the beads are covered with a layer of epoxy.

Recommended operating and storage temperature for the PC Beads is -55 °C to +125 °C.

Recommended Soldering Profile

Catalog Drawing
3D Model

PC Beads can be supplied with lower component heights “C”. Also, the wire length “F” can be modified to specific requirements.

Weight: 6 (g)

Dimmmmm tolnominal inchinch misc.
A11.2-0.500.431_
B11.2-0.500.431_
C11.8Max0.464Max
D2.54±0.100.1_
E7.6±0.200.299_
F2.79±0.250.110_
G0.65_022 AWG

Chart Legend
+ Test frequency

Typical Impedance (Ω)
10 MHz142
25 MHz+224
100 MHz+372
250 MHz402

PC Beads are controlled for impedance only. Minimum impedance values are specified for the + marked frequencies. The minimum impedance is typically the listed impedance less 20%.

Catalog Drawing

The PC Beads in 44 material are measured on the E4990A Impedance Analyzer. The 52 PC Beads are tested for impedance on the E4991A / HP4291B Impedance Analyzer.

Typical Impendance (Ω)
10 MHz 142
25 MHz+ 219
100 MHz+ 338
250 MHz 335

CSV Download

A NiZn ferrite developed to combine a high suppression performance, from 30 MHz to 500 MHz, with a very high DC resistivity.

Available in 44 material:
SM Beads
PC Beads
Wound Beads
Round Cable Snap-Its
Connector EMI Suppression Plates

44 Material Characteristics
Property Unit Symbol Value
Initial Permeability@ B < 10 gauss µi 500
Flux Density @ Field Strength Gauss
Oersted
B
H
3000
10
Residual Flux Density Gauss Br 1100
Coercive Force Oersted Hc 0.45
Loss Factor @ Frequency 10 -6
MHz
Tan δ/ µi 150
1.0
Temperature Coefficient of Initial Permeability (20 -70°C) % / °C 1.6
Curie Temperature °C Tc >160
Resistivity ohm-cm ρ 1×109

**** Characteristic curves are measured on standard Toroids (18/10/6 mm)  at 25°C and 10 kHz unless otherwise indicated. Impedance characteristics are measured on standard shield beads (3.5/1.3/6.0 mm) unless otherwise indicated.

Material Safety Data Sheet (MSDS)

Click here to download Complex Permeability vs. Frequency (CSV)

Ferrite Material Constants

Specific Heat
0.25 cal/g/°C
Thermal Conductivity
3.5 - 4.5 mW/cm-°C
Coefficient of Linear Expansion
8 - 10x10-6/°C
Tensile Strength
4.9 kgf/mm2
Compressive Strength
42 kgf/mm2
Young's Modulus
15x103 kgf/mm2
Hardness (Knoop)
650
Specific Gravity
≈4.7 g/cm3
The above quoted properties are typical for Fair-Rite MnZn and NiZn ferrites.


Storage and Operating Temperature
Printer Friendly Data Sheet - Download as pdf file

Go to Top