Inductive Components

Parts intended for tuned circuits, energy storage / transfer and transformers. All parts are rated for inductance factor and most for losses at applicable frequencies.

Suppression Components

Parts intended for EMI suppression of frequencies above 1 MHz, all parts are specified for impedance at applicable frequencies.

Absorber Tiles

Tiles optimally designed for absorption of radiated emissions for anechoic EMC test chambers.

Engineering Kits

Engineering Kits

Open Magnetic Circuit

Components with a fixed air gap in the magnetic path allowing higher current operation at the expense of inductance.

Closed Magnetic Circuit

Components with no air gap within the magnetic path enabling maximal inductance per unit volume for the specific design shape.

Board Component

Components of a size suitable for installing on both through-hole or surface mount printed circuit boards.

Cable Component

Components suitable for slipping or clamping onto cables, cable harnesses and system interconnects.

Rods

General purpose rod shapes (solid and with a hole through) useful for power transformers, sensors, antennas and differential and common mode chokes.

Antenna/RFID Rods

Solid rod shapes specifically developed for RFID Antennas operating up to 50 MHz.

Bobbins

Simple design method for power and EMI suppression chokes.

Toroids

Available in the widest selection of materials; the ring shape allows most efficient utilization of intrinsic material characteristics. Intended for filters, low power and broadband transformers. Conformal coating available.

Pot Cores

Maximal inductance per unit volume with high degree of self-shielding in mated pairs. Can be used as core halves for inductive proximity sensors.

E Cores

Economical mated pair design for high power inductors and transformers.

E Cores

Economical mated pair design for high power inductors and transformers.

I Cores

Mating piece for E-I and U-I configurations.

U Cores

Economical mated pair design for high power inductors and transformers.

EMI Suppression Bead

Tubular shapes which can be installed on the leads of other components or jumper wires. With inner diameters less than 6.5 mm, can also be used on small cable harnesses.

Beads-on-Leads

EMI suppression beads, affixed onto tinned copper wire, suitable for through-hole printed circuit boards.

PC Beads (through hole)

Multi-line suppressors can be used independently or series additive, usable in data or power lines.

Wound Beads

Six and eleven hole beads available with various winding configurations which provide moderately high impedance levels over broadband frequencies.

Multi-aperture cores

Dual hole cores useful for EMI suppression or as broadband transformers.

SM Beads (Differential-Mode)

Surface mount beads suitable for data line signal rejection and power line decoupling.

SM Beads (Common-Mode)

Surface mount beads which provide common mode signal rejection, with minimal impact to the desired differential signal.

Chip Beads

Surface mount multi-layer suppression beads allow high impedance in a small size.

Chip Arrays

Multi-line surface mount suppressors in 1206 size for data lines.

Engineering Kits

Engineering Kits

Round Cable EMI Suppression Cores

Tubular shapes with inner diameters from 3 to 36 mm, available material grades for effective EMI suppression between 1 MHz and 1+ GHz.

Round Cable Snap-its

Convenient clamp-on devices, not requiring disassembly of cable end terminations, useful for EMC testing and product retrofits. For cables as small as 2 mm up to 25 mm diameters.

Flat Cable EMI Suppression Cores

Cable suppression cores for ribbon cables with widths 12 to 76 mm.

Flat Cable Cores Assembly Clips

Accessories for split flat cable core assemblies.

Flat Cable Snap-its

Flat cable core assemblies with plastic cases in widths 33 to 64 mm.

Connector EMI Suppression Plates

Multi-hole plates with high electrical signal isolation, suitable for suppression above 25 MHz.

Miscellaneous Suppression Cores

Non-typical shapes and materials.